Now, when you press VOL+, VOL-, or Mute, the volume of the ZVOX system is controlled regardless of whether the Comcast remote is in the TV mode or Cable mode. Hold down the Setup Button While holding it, press 9, 8, and 1 in sequence You will see the LED flash If it doesn’t flash, repeat the procedure Of course, now that it is unpaired, you need to pair it back. Enter 9 - 9 - 3 (the AUX key blinks twice) and then press AUX once. Then, press and hold Setup until the AUX key blinks twice, then release Setup.Ģ. Press AUX once, then press and hold Setup until the AUX key blinks twice, then release Setup.Ģ. On the Comcast remote control, press AUX once. Then press and hold SETUP until the AUX key blinks twice, then release Setup.Ģ. Factory Reset the Xfinity Voice Remote with a Setup Button (XR11) If the buttons on your Voice Remote (model XR11) are still unresponsive, you may need to perform a factory reset. Part 2: Configure your Comcast remote Activate the AUX functionġ. While the speaker is ON press and hold Other Settings for 5 seconds until PS-0 starts flashing then release and adjust with the remotes volume button, move it to PS-5.įor Original SB Soundbars (SB380, SB400, SB500, SB700):Ī) While the speaker is ON Press and hold down the Mute & Volume Up buttons on the side of the speaker until you see “PS” on the display.ĭ) Wait until the “PS-5” display disappears. If you have a Panasonic TV, use the alternate instructions below.įor Soundbase on the front panel of the ZVOX Audio speaker: (570, 670, 770):Ī) While the speaker is ON Press and hold down the Mute & Volume Up buttons until you see “PS” on the display.Ĭ) Press and release the Volume Up button until you see “PS-5” (“PS-3” for Panasonic TV)ĭ) Wait until the “PS-5” display disappears.įor systems with the Other Settings Button on remote (AV200, AV201, AV155, AV157, AV203, New Version SB380, SB500, SB700): The following instructions apply to any TV brand except Panasonic. These instructions describe how to configure your Comcast cable remote to control the volume from your ZVOX Audio system and not from your TV. Now, depending on your TV manufacturer, enter the five-digit code. In case you are pairing it to a TV, press and hold down the Xfinity and Mute buttons on your remote for about 5 seconds until the light at the top of the remote changes from red to green. Being able to control the TV and arduino with a single remote would be ideal.Comcast Custom DVR 3-Device Universal Remote Control After your remote has been paired, see if the problem goes away. I'm basically trying to simplify things by reducing the need for additional remotes (since I know I could just get a different one and use that with the arduino instead). In this way it would be like im "borrowing" one of these buttons to do something separately to an arduino near a TV thats being watched all while the arduino is receiving RF signals and not interfering with TV watching. These buttons typically do nothing when pressed and are rarely ever pressed by the user anyways. There are a handful of "useless buttons" on this remote (that send RF only) that would work great for what im trying to do. Either the TV would have to be shut off in order for the arduino to receive input from the remote or each time the volume is adjusted on the remote it triggers the arduino's response which isnt really what im looking for. These are the power buttons and volume buttons. The remote only has a few buttons that send IR. I still want the remote to function properly as it will be in use with a TV and arduino simultaneously. Isn't it easier to decode the IR signal of the remote instead of the RF signal.įor what I'm trying to accomplish, no. Is there something I'm missing? Am I going about this the wrong way? Would I need a different kind of receiver module or is there some other issue why this receiver isnt working with this remote? Any guidance would be appreciated I've used the included 433MHz transmitter in a separate test to verify that the receiver is working.Īm a bit confused how this can be accomplished with this specific remote. I assumed this thing could just receive any kind of signal from any kind of RF remote working on this frequency, but it receives nothing when buttons are pressed on the Xfinity remote (I'm using the rc-switch library ). I've tried looking around online for answers and eventually ended up getting a generic 433 MHz receiver from amazon (WayinTop) thinking this would somehow be able to get the job done (which it didnt). This remote has buttons that sends both IR and RF, and I'd like to be able to receive RF signals from this remote specifically on an arduino to trigger sending out data from the arduino in response to button presses on the remote (to keep it simple, lets just assume the arduino is controlling an LED each time a certain button on the Xfinity remote is pressed).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |